Troubleshooting • Re: cannot get APT to update
I saw another post.I rebooted my router and apt started to work correctly and i managed to update and upgrade my system.What is that all about ?????Statistics: Posted by pjzpi — Mon Dec 23, 2024 3:01 pm
View ArticleClik here to view.
Media centres • Re: Peppy player
To select the Nixie Tube Clock screensaver you need to select a screensaver type 'image':https://github.com/project-owner/Peppy/ ... fig.txt#L2and set the property 'image.folder' to the...
View ArticleClik here to view.
Raspberry Pi OS • Re: Pi5 with one partition exFat
OP was talking about booting his RPi5..... Statistics: Posted by KeithMck — Mon Dec 23, 2024 3:32 pm
View ArticleClik here to view.
HATs and other add-ons • Re: NVMe overheating issues with GeekWorm dual NVMe hat
Here is my experience with Geekworm X1004 NVME temperatures ...I tested around 7 different NVMEs in last week, with termal camera too...Booted from SD card and tested drives are always at IDLE state...
View ArticleBeginners • Re: Remote access to drive connected to Raspberry Pi
I'm sure there are no problems with network. Pi is connected to 300Mbps internet speed with LAN cable, and I can locally connect to smb drive and the copy-paste speeds of files are very decent ~ 30...
View ArticleGeneral discussion • Don't do this!
Desiring to mount my NAS to the new Raspberry Pi 5 on boot I edited the fstab and used /Home/"My account" as the mount point. I mean what could be wrong with that, when you make an SMB connection it...
View ArticleRaspberry Pi OS • Re: Clean install of Bookworm and rpicam apps was not included
Thank You for this explanation ...My reference to "Full Lite" was a bit "tongue in Cheek!!!"ThanksJohnWStatistics: Posted by ejwjohn — Tue Dec 24, 2024 3:15 pm
View ArticleClik here to view.
Troubleshooting • Re: Broken Pi 5 Repair
I can't help you with identifying that part, but it looks like that is not the only problem with that Pi.There is also what looks like a broken resistor near by.You should check the rest of the board...
View ArticleMicroPython • Re: Building an Internet-Radio using a Pico W using just Python
The postman was so kind to deliver two new and shiny Pico 2 Ws today on Christmas Eve. I soldered headers onto one of them and checked.Playback of my 64 kbit stream still shows irregulars reconnects...
View ArticleBeginners • Re: Compatability of multiple devices and a single pi 5
So the DWM1001-dev board says it uses the I2c connections as well, so this would interfere with the AI hat+ board? Or is there a way to set up the DWM1001 to not use I2c? I would add in the...
View ArticleCamera board • Re: Ideas to permanently connect RPi camera to Pi zero w
I must have tried everything to set up a few dozen cameras attached to the Pi Zero without ever finding the perfect solution. At some point, things start to move. Especially if the device is often...
View ArticleAdvanced users • Re: Testing class A2 SD cards with Command Queueing on Pi 5
Implementing an allow-list is at least as indiscriminate as disabling CQ for certain cards. There are few parameters that change between incremental revisions of a card's firmware. For example, I...
View ArticleAdvanced users • Re: using a 2nd SD card on the PI4 blocks all IO when using...
Tagging this so I can come back to it later.Can you see what process is active under the failure condition? e.g. top or iotop. Additionally, can you do vmstat 2 when a) IO is "blocked" and b) when IO...
View ArticleAdvanced users • Re: Setting gpio pullup in kernel module that is using the...
That's one way to do it. But there's no "just" about it - it takes quite a bit of knowledge to get to that point.Statistics: Posted by PhilE — Tue Dec 24, 2024 4:20 pm
View ArticleDevice Tree • Re: How to use dt-blob.bin on CM5
There is no dt_blob.bin for the Pi 5 family - you should use Device Tree. For some scenarios you may find that the gpio= config.txt setting is sufficient.I suggest you don't rely on internal pull-ups...
View ArticleGeneral discussion • Re: New Raspberry Pi Products
We'll stop after we release a product and the launch post attracts zero whiny comments in a week.So....never. Amazing how people get so upset because a brilliant new product doesn't have some niggling...
View ArticleTroubleshooting • Re: FAT error on official starter kit
what i'd do:1) update the bootloaderhttps://www.raspberrypi.com/documentati ... ate_stableNOTE: it overwrites the SD card with the bootloader... use a spare card or be prepared to reload the card with...
View ArticleGeneral discussion • Re: Power supply - alternative needed to plug type
Could maybe use extra long GPIO extension or just use a USB C pigtail.https://thepihut.com/products/stacking- ... all-headerhttps://amzn.eu/d/iwXW7unStatistics: Posted by rpiMike — Wed Dec 25, 2024...
View ArticleOfficial Display • Re: Changing resolution of Touch Display 2
Thanks for the suggestion. Perhaps the complaints about the cursor image size appear only for certain scale factors. I am using --scale=1.3. I suppose that cursor images are available only in certain...
View ArticleMicroPython • Re: Cannot get 2nd LED to activate
In the code, the first line "From" should be "from".Coding with thonny ? Are there error messages displayed?Statistics: Posted by ghp — Wed Dec 25, 2024 3:58 pm
View Article